civil engineering-->>Quantity Of Materials Required For Concrete Work

for more information click on this link engineering

Quantity Of Materials Required For Concrete Work

The Following are the Quantity Of Materials Required for the Concrete Works Of Different Types

1) P.C.C. With Graded Stone Chips ===>

For 10 cu.m. Of Plane Cement Concrete Work with Graded Stone Chips

For M10 Grade :-

Cement @ 1.54 cu.m or 45 Bags
Sand @ 4.62 cu.m or 133 Bags
Stone Chips @ 9.24 cu.m. or 266 Bags.

For M15 Grade :-

Cement @ 2.2 cu.m or 65 Bags
Sand @ 4.4 cu.m or 127 Bags
Stone Chips @ 8.8 cu.m. or 254 Bags.

For M20 Grade :-

Cement @ 2.8 cu.m or 81 Bags
Sand @ 4.2 cu.m or 121 Bags
Stone Chips @ 8.4 cu.m. or 242 Bags.

For M25 Grade :-

Cement @ 3.85 cu.m or 111 Bags
Sand @ 3.85 cu.m or 111 Bags
Stone Chips @ 7.7 cu.m. or 222 Bags.

2) P.C.C. With Brick Ballast or Brick Chips ===>

For 10 cu.m. Of Plane Cement Concrete Work with Brick Ballast

For M5 Grade :-

Cement @ 1.00 cu.m or 29 Bags
Sand @ 5.00 cu.m or 144 Bags
Brick Ballast @ 10.00 cu.m. or 288 Bags.

For M10 Grade :-

Cement @ 1.23 cu.m or 36 Bags
Sand @ 4.92 cu.m or 142 Bags
Brick Ballast @ 9.85 cu.m. or 284 Bags.

For M15 Grade :-

Cement @ 2.29 cu.m or 66 Bags
Sand @ 4.57 cu.m or 132 Bags
Brick Ballast @ 9.14 cu.m. or 264 Bags.

3) R.C.C. With Graded Stone Chips ===>

For 10 cu.m. Of Reinforced Cement Concrete Work with Graded Stone Chips, The Amount Of Cemnet, Sand, Stone Chips Requred are same as that of the P.C.C.

Quantity Of Steel Required

For Normal Slab, Chajja, Lintel = 785kg or 0.785 Ton
For Roof Slab = 1180kg or 1.18 Ton
For Stair = 1570kg or 1.57 Ton
For Column and Beams = 1960kg or 1.96 Ton

Quantity Of Binding ( Black Annealed Wire) Wire Requred

For Normal Slab, Chajja, Lintel = 0.785kg
For Roof Slab = 1.18kg
For Stair = 1.57kg
For Column and Beams = 1.96kg

Comments

civil engineering-->>Determinacy, Indeterminacy and Stability of Frames

Determinacy, Indeterminacy and Stability of Frames : Structural engineers must be able to apply judgment rather than stated rules. The most important aspect of structural design is not the ability to apply formulas or manipulate mathematics. The most important skill for the structural engineer is to be able to stand back, look at a drawing or sketch and determine whether a structure is stable, and if it is stable, to be able to determine how it will carry the applied loads. For a very complicated structure this might be more difficult and a computer can provide some help, but ultimately it is the skill and concern of a good structural engineer which produces good structural designs which have integrity. Another important closely related skill is the ability to determine whether, and to what degree, a structure is statically indeterminate. There really aren’t many rules and rules may be difficult to apply in any case. For this reason, we need experience. A skilled structural...

civil engineering-->>Asphalt Binder Modifiers

Asphalt Binder Modifiers Some asphalt cements require modification in order to meet specifications. Asphalt cement modification has been practiced for over 50 years but has received added attention in the past decade or so. The added attention can be attributed to the following factors (Roberts et al., 1996): Increased demand on HMA pavements . Traffic volume, loads and tire pressures have increased substantially in recent years, which can cause increased rutting and cracking. Many modifiers can improve the asphalt binder's stiffness at normal service temperatures to increase rut resistance, while decreasing its stiffness at low temperatures to improve its resistance tothermal cracking. Superpave asphalt binder specifications . Superpave asphalt binder specifications developed in the 1990s require asphalt binders to meet stiffness requirements at both high and low temperatures. In regions with extreme climatic conditi...

civil engineering-->>QUESTION BANK ON SURVEYING

FOR CIVIL ENGINEERING-->>> 1. Define Tacheometer. It is an ordinary transit theodolite fitted with an extra lens called analytic lens. The purpose of fitting the analytic lens is to reduce the additive constant to zero. 2. Define Substance bar: A Substance bar is manufactured by Mr. Kern. The length of the substance bar is 2m (6ft) for measurement of comparatively short distance in a traverse. A Substance bar may be used as a substance base. The length of the bar is made equal to the distance between the two targets. 3. What do you mean by Fixed hair method: In this method, the stadia wires are fixed (or) fitted at constant distance apart. 4. State Stadia intercept: The difference of the distance between the top and bottom cross hairs is called as staff intercept 5. What do you mean by tangential method: In this method, the stadia hairs are not for taking readings. The readings being taken against the horizontal cross hair. . 6. The tangential method: In...

CE

Search This Blog